| |
REPSOL SUPER TAURO 150
Description
These Oils are aimed at all types of industrial gears including those which are heavily loaded and which work under severe conditions. They are manufactured from selected high viscosity base stocks with special additives to improve their anti-oxidation, anti-foam, anti-rust properties etc. Sulphur-Phosphor based additives give them their excellent extreme pressure properties (EP).
Recommended uses
These oils are designed for use in all types of industrial gears whether lubricated by splash or circulation.
They are recommended for those applications requiring the highest levels of oxidation prevention and/or load capacity.
Properties
Not corrosive to Copper and its alloys.
Good water separation capacity.
Outstanding oxidation resistance.
Very good rust protection.
Good non-foaming properties.
High load capacity.
Strong lubricating film.
Quality level
DIN 51517 Part 3 CLP
ISO 6743/6 - ckc
CINCINNATI MILACROM P-35, P-59, P-63,
P-76, P-77, P-74 and P-78
US Steel 224
AGMA 9005-D94
David Brown S1.53.101
- |
UNIT |
Method VALUE VALUE VALUE VALUE VALUE VALUE VALUE VALUE |
VALUE |
VALUE |
VALUE |
VALUE |
VALUE |
VALUE |
VALUE |
VALUE |
ISO Grade |
- |
- |
68 |
100 |
150 |
220 |
320 |
460 |
680 |
1000 |
Viscosity,
100¡İC |
cSt |
ASTM D445 |
8,9 |
11,3 |
14,8 |
18,7 |
23,7 |
29,8 |
40,0 |
51 |
Viscosity,
40¡İC |
cSt |
ASTM
D 445 |
68 |
100 |
150 |
220 |
320 |
460 |
680 |
1000 |
Viscosity
Index |
- |
ASTM
D 2270 |
100 |
98 |
95 |
94 |
98 |
92 |
95 |
95 |
Pour Point |
¡İC |
ASTM
D 97 |
-12 |
-12 |
-12 |
-12 |
-12 |
-12 |
-12 |
-12 |
Flash Point |
¡İC |
ASTM
D 92 |
190 |
195 |
200 |
205 |
210 |
215 |
220 |
220 |
Demulsibility
Free water
Mulsibility |
Cm3
Cm3 |
ASTM
D 2711 |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
80 min
1 max. |
Cooper corrosion,
3h. 100¡İC |
ASTM
D 130 |
- |
1b |
1b |
1b |
1b |
1b |
1b |
1b |
1b |
Rust, methods A and B |
- |
ASTM
D 665 |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
TIMKEN OK |
lb |
ASTM
D 2782 |
55 |
60 |
65 |
70 |
70 |
70 |
70 |
70 |
FZG, tage 12 |
- |
DIN 51354 |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
Pass |
Available in
875 containers ISO grades 220 and 320, and 185 Kg. drums all ISO grades.
Hazard Identification
This product is not classified as toxic or hazardous under current legislation.
Handling
Certain minimum precautions to avoid prolonged contact with the skin should be taken when handling. The use of gloves, visors or masks is recommended in order to avoid splashes.
Health and safety hazards
Inhalation: Minimum risk of inhalation as it is a non-volatile product.
Ingestion: Does not provoke vomiting. Drink water. Seek medical assistance.
Contact with Skin: Wash with abundant water and soap.
Eyes: Wash with abundant water.
General measures: Seek medical assistance.
Fire fighting measure
No special measures are required.
Fire control: Foams, dry chemicals, CO2, water spray. Do not apply water jet directly as this may cause the product to spread.
Environmental precautions
Danger of physical contamination in the case of spillage (water flows, coastal areas, the ground, etc.) due to its floating capacity and oily consistency which may cause damage to fauna and florawith which it comes into contact. Avoid its penetration into water containers or outlets.
Decontamination and cleaning: Treat as an accidental oil spillage. Avoid spreading by using mechanical barriers and eliminate using both physical and chemical means. |
|
